Here are some common troubleshooting steps you can try if your re:Mix does not start:&#x26A0;&#xFE0F; Sharp blades, handle with caution.&#x26A0;&#xFE0F; Due to the safety features, the blades do not rotate without a jar on.&#xA0;1. Make sure the blender is plugged into the power source.2. Ensure that the jar is locked in on the blades head.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026072808-4c47de57-25d8-4e1a-89c5-a6991fd22894-1.jpg" style="width: 698px;" class="fr-fic fr-dii">3. Rotate/readjust the jar to get a snug fit.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026072812-fdb76f84-196d-40a3-a7ef-72418206db76-untitled%20design.jpg" style="width: 468px;" class="fr-fic fr-dii">4. Try a different jar. (certain jars might have imperfections and have a hard time getting detected.)<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026072813-ff428e57-7618-405c-b1a0-d8f76f55169d-dscf2764.jpg" style="width: 229px;" class="fr-fic fr-dii">5. Check that there is no residue or debris between the jar and the blender head.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026072813-e41e1ade-7b6b-4794-a21b-dc30387598a7-2.jpg" style="width: 484px;" class="fr-fic fr-dii">&#x26A0;&#xFE0F; Due to the safety features, the blades do not rotate without a jar on.&#xA0;6. Rotate the blades head unto the mixer body until you hear a &quot;click&quot;.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026072814-3cbe583f-1cc8-4a17-8c58-b3d48e8d59de-3.jpg" style="width: 610px;" class="fr-fic fr-dii">If the above steps do not work, try:7. Unplug the mixer and let it cool for an hour before attempting to use it again.(Your re:Mix has an internal thermal breaker that shuts off the motor when it overheats)OR8. Manually check if the motor is working by removing the blade head, turning the knob to 1 and carefully press your finger on the detection pin, <a href="https://drive.google.com/file/d/1QVJhj2EzXnHSsII_KC7DsH479rcQd2OQ/view?usp=sharing" target="_blank" rel="noopener noreferrer">as shown</a>.9. If the motor does not rotate, please request a repair by contacting us.10. If the motor rotates, there is an issue with the blades head. You may choose to order a replacement or contact us if the product is under warranty.

Le re:mix ne démarre pas ou a des problèmes de fonctionnement

There should be 0 leaking from the blades head.As indicated in the user manual, the material of the head can get damaged, and the head locker can come loose if you:<ul><li>Blend foods above 40 degrees Celcius</li><li>Dishwash the head</li><li>Wash or soak the head in hot water</li></ul><h2 id="1-did-you-open-the-blades-head-for-deep-for-cleaning">1. Did you open the blades head for deep for cleaning?</h2><ul><li>Yes, continue</li><li>No, see point 2</li></ul><h3 id="check-the-sealing">Check the sealing</h3>Make sure the parts are assembled as shown below. Take special attention that the 4 large rings of silicone seal are facing the metal plate.<h2 id="2-tighten-the-head-unto-the-jar">2. Tighten the head unto the jar</h2>Make sure that you are tightening the head well on the jar. It should feel like screwing a lid to the maximum.<h2 id="3-contact-us">3. Contact us</h2>If you tried these steps in the right order, and are still experience issues, contact us at <a href="mailto:hello@openfunk.co" rel="nofollow noopener noreferrer" target="_blank">hello@openfunk.co</a>. To help solve your case quickly, please describe the issue in detail, include pictures and videos if possible, and add mention your order number.

La tête des lames fuit

Use this guide to exchange the back and front panels of your re:Mix.&#xA0;To proceed to the exchange you will need the following tools:<ol><li>Screwdriver with Torx 10 (T10) tip (if electric, use only in case it has an adjustable Torque)</li><li>Screwdriver with 3mm flat-tip&#xA0;</li></ol>&#x26A0;&#xFE0F; Before starting any operation, ensure your re:Mix is unplugged from the electric socket, otherwise you may get a life-threatening electric shock.&#xA0;IMPORTANT NOTES<ul><li>Do not use an electric screwdriver if it does not have a minimum Torque of 0,2 Nm otherwise you could end up damaging the plastic thread of the screw socket.</li><li>If you use a manual screwdriver, and therefore you cannot use the Torque units to limit the amount of force to screw, only screw until you feel resistance otherwise it might damage the plastic thread of the screw socket.</li><li>Be aware that when mounting the back and front panels, the screw head may not be perfectly aligned with the panel surface, meaning that the screw might be slightly sticking in or out.</li></ul> <h2 id="step-1---remove-the-back-panel">STEP 1 - Remove the back panel</h2>Take your re:Mix and place it upside-down on your working desk.Use your manual screwdriver with a Torx-10 tip, or your electric one set on Torque 0 (0,2 Nm) and start unscrewing the 4 screws of the back panel.&#xA0;<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-8351cff5-1768-45e1-ad67-f68441c2d2c4-89c75ddd-bfdc-4460-b23b-6490db30ad89.png" style="width: 300px;" class="fr-fic fr-dii">Now, your back panel is ready to be removed!<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-719388ca-94a7-4b4e-8de1-5574199d5030-fdb56d6a-5eb9-4ca8-b1af-e0929a69546d.png" style="width: 300px;" class="fr-fic fr-dii"><h2 id> </h2><h2 id="step-2---remove-the-front-panel">STEP 2 - Remove the front panel</h2>Turn your re:Mix and start unscrewing the next 4 screws of the front panel.&#xA0;<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-d8d612c8-0a5f-42cb-b37b-763c58cbb78f-f6445f80-fb60-4a21-b5d6-bdaf591a4973.png" style="width: 300px;" class="fr-fic fr-dii"><h2 id="step-3---remove-the-switch-component">STEP 3 - Remove the switch component</h2>Unscrew the switch from the front panel.Use your manual screwdriver or your electric one with a Torx-10 tip, set on Torque 1 (1/1,2 Nm) and unscrew the 2 screws, which hold the switch attached to the front panel.&#xA0;<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-acf3acd9-37e1-4368-ad70-7a9e0d6a6737-36ffccf5-27a9-4332-a6d5-32b0975960e0.png" style="width: 300px;" class="fr-fic fr-dii"><img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-bf1f8d0a-e192-43d3-9057-4cf9c1c2de29-09dcdf5b-1a52-42b1-a27c-a5eac3cbb086.png" style="width: 300px;" class="fr-fic fr-dii"><h2 id="step-4---remove-the-aluminium-knob">STEP 4 - Remove the aluminium knob</h2>Now, it is time to remove the aluminium knob. To do so, you have to insert the flat-tip screwdriver into the small hole placed on the side of the knob. Unscrew the knob by turning the screwdriver just a few times.&#xA0;Do not unscrew completely or you might disassemble the components of the knob.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-06c2a548-86fa-43fe-bd4a-0f7bb72564ae-c9224f7b-8d3c-4306-8aa4-f01205fa23e5.png" style="width: 300px;" class="fr-fic fr-dii"><img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-a5aeb1bd-75fc-4c1e-acfe-6704fb0b9978-7d77e767-50b1-4d2c-a96d-a2f6f3096cf0.png" style="width: 300px;" class="fr-fic fr-dii">Detach the knob from the panel by grabbing the knob with your fingers and pulling it out.&#xA0; <h2 id="step-5---mount-the-switch">STEP 5 - Mount the switch&#xA0;</h2>Take your 2 new panels and prepare to do the inverse procedure to mount them on your re:Mix.Start with the front panel.&#xA0;<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-d5ae90c4-a6f0-4c53-a713-85f89de6d4d9-9fdc4261-b7c9-48b9-8527-319a2e6e9f89.png" style="width: 300px;" class="fr-fic fr-dii">The first thing to do here is to attach the switch component to the panel.&#xA0;<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-2f9aaad3-6c31-49fa-b042-6dd1e5e39709-a20f3c80-91bf-48f4-95fc-439e47eae368.png" style="width: 300px;" class="fr-fic fr-dii"><img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-15a5aeab-b54f-4781-a3e3-2b715fe93b0b-f7668150-ffaa-4f8a-be85-f7b199b0c155.png" style="width: 300px;" class="fr-fic fr-dii">Be very careful to set-up the switch in the correct position: &#xA0;The pin switch that sticks out of the panel has a round and a flat side. The flat side must be facing the opposite side of the sticker as you can see in the picture below.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-96417f1c-2870-41e2-8eb0-876ae1c5aa05-fea223c4-de5a-4925-85c2-31b34da3175a.png" style="width: 300px;" class="fr-fic fr-dii">When the switch is set up correctly fix it back onto the panel with its 2 original screws.Use your manual screwdriver or your electric one with a Torx-10 tip set on Torque 1 (1/1,2 Nm).<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-8c2aebef-09ee-4521-bba3-b58e9501caca-28e73201-a260-4832-b08b-38967b2b51ed.png" style="width: 300px;" class="fr-fic fr-dii"><h2 id="step-6---mount-the-knob">STEP 6 - Mount the knob</h2>Take the knob and by pressing with your finger, attach it to the pin of the switch.The knob is set correctly if the speed indicator is pointing towards the sticker on position 0.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-aa3374cc-5721-4b0f-8211-530dfc82666e-a7a4fa7a-5c59-4212-a8a7-64000a8407b1.png" style="width: 300px;" class="fr-fic fr-dii"><img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-06123a9b-2d0a-4518-ba1e-3425156a59dd-223ac0ce-f4ea-4990-84dc-96b1037d2af4.png" style="width: 300px;" class="fr-fic fr-dii">Once the knob is properly set up, take the flat-tip screwdriver, insert it into the small hole placed on the other side of the knob and screw it until you feel it is tight.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-bb1aab41-0433-47eb-a074-7c3d79c607ed-c413495c-7257-4059-8a1f-c13050c2c481.png" style="width: 300px;" class="fr-fic fr-dii"><h2 id="step-7---mount-the-front-panel-onto-the-remix">STEP 7 - Mount the front panel onto the re:Mix</h2>Use your manual screwdriver or your electric one with a Torx-10 tip, set on Torque 0 (0,2 Nm) and screw back the 4 screws of your front panel.&#xA0; <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2025021121-4f7113e1-429c-411d-93d0-c1fa9981c25f-f51e7057-5d0b-4de0-b228-f949c972a3fd.png" style="width: 300px;" class="fr-fic fr-dii">&#xA0;<h2 id="step-8---mount-the-back-panel-onto-the-remix">STEP 8 - Mount the back panel onto the re:Mix</h2>Use your manual screwdriver with a Torx-10 tip, or your electric one set on Torque 0 (0,2 Nm) and screw back the 4 screws of your front panel.<img data-fr-image-pasted="true" src="https://downloads.intercomcdn.com/i/o/1150677347/352f79e7502c8e940703537c/WhatsApp+Image+2024-08-19+at+14_27_40.jpeg?expires=1739394000&amp;signature=9b98dde62bf8fe145c392a9c73d310c42c9861b7f54f5bba466b05e24d9b4803&amp;req=dSEiFs95moJbXvMW3Hu4gVH%2BxS1QQyrzozvGyprvFfbeZ09QNMNv48igg%2FS%2F%0AfQ%3D%3D%0A" style="width: 300px;" class="fr-fic fr-dii">

Comment échanger les panneaux arrière et avant

<h2 id="isPasted">&#x1F551; 10 - 15 minutes&#xA0; &#xA0;&#x1F527; moyen - facile</h2> <h2 data-start="341" data-end="361" id="informations-sur-le-guide">Informations sur le guide</h2>La t&#xEA;te aux lames du mixeur Open Funk re:Mix peut &#xEA;tre d&#xE9;mont&#xE9;e pour le nettoyage, l&apos;entretien ou le remplacement de certaines pi&#xE8;ces. Ce guide vous explique la proc&#xE9;dure &#xE9;tape par &#xE9;tape. Avant de commencer, assurez-vous que le mixeur est d&#xE9;branch&#xE9; de la prise &#xE9;lectrique. Remarque : les lames sont tranchantes. Manipulez toutes les pi&#xE8;ces avec pr&#xE9;caution pendant le d&#xE9;montage. Une fois la proc&#xE9;dure termin&#xE9;e, assurez-vous que toutes les pi&#xE8;ces sont propres, correctement align&#xE9;es et solidement remont&#xE9;es avant utilisation. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021812-8c96f4a2-e802-45e8-8b06-783d9c366e39-blades%20head.jpg" style="width: 679px;" class="fr-fic fr-dii"><h3 id="outils">Outils</h3><ul><li>D&#xE9;verrouilleur</li><li>Tournevis cruciforme PH00</li></ul><h3 id="&#xE9;tapes-de-r&#xE9;paration">&#xC9;tapes de r&#xE9;paration</h3><ul><li>&#xC9;tape 1 - Retirez la goupille</li><li>&#xC9;tape 2 - Retirez le verrou</li><li>&#xC9;tape 3 - Retirez les lames</li><li>&#xC9;tape 4 - Retirez le joint en joint d&#x2019;&#xE9;tanch&#xE9;it&#xE9;</li><li>&#xC9;tape 5 - D&#xE9;vissez les but&#xE9;es</li><li>&#xC9;tape 6 - Retirez les glissi&#xE8;res et les ressorts</li><li>Nettoyage et inspection</li></ul> <h2 data-start="130" data-end="163" id="&#xE9;tape-1---retirez-la-goupille">&#xC9;tape 1 - Retirez la goupille</h2><ol><li>Utilisez le d&#xE9;verrouilleur : alignez le c&#xF4;t&#xE9; du d&#xE9;verrouilleur avec la rainure arrondie du verrou.</li><li>Glissez d&#xE9;licatement le d&#xE9;verrouilleur sous la goupille.</li><li>Soulevez la goupille vers le haut pour la retirer.</li></ol>Conseil : assurez-vous que le c&#xF4;t&#xE9; du d&#xE9;verrouilleur s&apos;enclenche bien dans la rainure avant de soulever. Cela garantit un retrait propre sans endommager la goupille ou les pi&#xE8;ces environnantes. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-645daeb3-d37a-4468-8fac-82ed013e2b61-5%20-%20bh%20tool%20sliding%20under%20pin.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-a9fae5b9-74fd-43c3-98b6-394928ccea57-6%20-%20bh%20tool%20removing%20pin.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-9734dbd0-cab3-46a4-b284-279c93765f82-7%20-%20bh%20showing%20pin%20removed.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 data-start="137" data-end="172" id="&#xE9;tape-2---retirez-le-verrou">&#xC9;tape 2 - Retirez le verrou</h2><ol><li>Tenez fermement la t&#xEA;te aux lames.</li><li>Utilisez le d&#xE9;verrouilleur pour saisir le verrou et tournez-le dans le sens inverse des aiguilles d&apos;une montre pour le retirer.</li><li>Mettez le d&#xE9;verrouilleur et la goupille en lieu s&#xFB;r pour le remontage.</li></ol>Conseil : si n&#xE9;cessaire, le d&#xE9;verrouilleur peut &#xEA;tre tourn&#xE9; avec pr&#xE9;caution &#xE0; la main, mais veillez toujours &#xE0; bien tenir la t&#xEA;te aux lames. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021916-b0ea37c2-d48a-41c4-bbc9-047a29fec3b0-2%20-%20bh%20&amp;%20tool%20ready%20to%20be%20open.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-400556cb-f2f4-4722-bc09-10c6a1e54b7b-3%20-%20bh%20being%20unlocked.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-2cceb2d7-85ed-4bac-9c90-a440b6c95877-8%20-%20bh%20showing%20locking%20ring%20removed.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 id="&#xE9;tape-3---retirez-les-lames">&#xC9;tape 3 - Retirez les lames</h2><ol><li>Tenez fermement le cadre de la t&#xEA;te d&apos;une main pour le maintenir stable.</li><li>Saisissez les lames avec pr&#xE9;caution par l&apos;engrenage.</li><li>Soulevez les lames vers le haut pour les extraire du cadre.</li></ol>Conseil : placez un torchon entre votre main et la t&#xEA;te aux lames pour vous prot&#xE9;ger des lames tranchantes. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-c6e56305-83fc-4adc-8f79-bacece23c932-9%20-%20bh%20-%20showing%20without%20locking%20ring.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-2108a934-5a07-4033-af02-98ffe0aa573e-10%20-%20bh%20removing%20blade%201.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-25125365-24a0-400b-8f22-8ff8affa7fea-11%20-%20bh%20removing%20blade%202.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 data-start="0" data-end="41" id="&#xE9;tape-4---retirez-le-joint-en-joint-d&#xE9;tanch&#xE9;it&#xE9;">&#xC9;tape 4 - Retirez le joint en joint d&#x2019;&#xE9;tanch&#xE9;it&#xE9;</h2><ol><li>Rep&#xE9;rez le joint d&#x2019;&#xE9;tanch&#xE9;it&#xE9; &#xE0; l&apos;int&#xE9;rieur du cadre de la t&#xEA;te de lame.</li><li>Saisissez d&#xE9;licatement le joint avec vos doigts.</li><li>Soulevez le joint pour le retirer du cadre et mettez-le de c&#xF4;t&#xE9;.</li></ol>Conseil : m&#xE9;morisez l&apos;orientation du joint. Les c&#xF4;t&#xE9;s sup&#xE9;rieur et inf&#xE9;rieur sont asym&#xE9;triques et doivent &#xEA;tre r&#xE9;install&#xE9;s dans le m&#xEA;me sens. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-c42ea9b6-c71e-4071-a597-a0177bed1f04-12%20-%20bh%20removing%20head%20seal%201.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-33786373-3a97-4324-9fc8-1382bcfa95e2-13%20-%20bh%20removing%20head%20seal%202.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-d3401462-c609-4b38-9e84-fddc272eebcf-14%20-%20bh%20showing%20removed%20seal.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 id="&#xE9;tape-5---d&#xE9;vissez-les-but&#xE9;es">&#xC9;tape 5 - D&#xE9;vissez les but&#xE9;es</h2><ol><li>Rep&#xE9;rez les but&#xE9;es fix&#xE9;es par des vis cruciformes &#xE0; l&apos;int&#xE9;rieur du cadre de la t&#xEA;te aux lames.</li><li>Utilisez le tournevis cruciforme PH00 pour desserrer chaque vis en la tournant dans le sens inverse des aiguilles d&apos;une montre.</li><li>Retirez les vis et les but&#xE9;es, puis mettez-les de c&#xF4;t&#xE9; en lieu s&#xFB;r pour le remontage.</li></ol>Conseil : utilisez un tournevis de taille appropri&#xE9;e pour &#xE9;viter de fausser les vis. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-1909f871-0a71-49ed-9aa1-cce081b037a5-15%20-%20bh%20removing%20%20stopper%20screws.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021916-0c6720e8-11e1-4a3a-a998-f66058d11b0e-extra%20screw%20photo.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-14df2026-e383-4101-af22-3ea3588d9628-16%20-%20bh%20removing%20stoppers.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h1 data-start="0" data-end="46" id="&#xE9;tape-6---retirez-les-glissi&#xE8;res-et-les-ressorts">&#xC9;tape 6 - Retirez les glissi&#xE8;res et les ressorts</h1><ol><li>Rep&#xE9;rez les glissi&#xE8;res situ&#xE9;es sous les but&#xE9;es.</li><li>Soulevez chaque glissi&#xE8;re pour la retirer du cadre de la t&#xEA;te aux lame et mettez-les de c&#xF4;t&#xE9;.</li><li>Retirez les ressorts situ&#xE9;s sous les glissi&#xE8;res et mettez-les de c&#xF4;t&#xE9; pour le remontage.</li></ol>Conseil : utilisez une pince &#xE0; &#xE9;piler ou une pince pour retirer et r&#xE9;installer les petits ressorts en toute s&#xE9;curit&#xE9; <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-b7d01461-6e24-4dab-a093-c946952ea36c-17%20-%20bh%20removing%20jar%20sliders.jpg" style="width: 669px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-b87b7151-058f-4d9c-8873-4bfe5b490e7c-extra%20spring%20photo.jpg" style="width: 663px;" class="fr-fic fr-dii"> <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021915-217467d5-202b-4ac7-ab9f-7749964c2100-18%20-%20bh%20removing%20springs.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 id="nettoyage-et-inspection">Nettoyage et inspection</h2>La t&#xEA;te aux lames &#xE9;tant enti&#xE8;rement d&#xE9;mont&#xE9;e, vous pouvez nettoyer toutes les pi&#xE8;ces &#xE0; fond. &#xC9;liminez tout r&#xE9;sidu ou accumulation &#xE0; l&apos;aide d&apos;eau, d&apos;une brosse douce ou d&apos;un chiffon. N&apos;utilisez pas d&apos;eau &#xE0; plus de 40 &#xB0;C, car des temp&#xE9;ratures plus &#xE9;lev&#xE9;es pourraient endommager les mat&#xE9;riaux. Assurez-vous que tous les composants sont compl&#xE8;tement secs avant le remontage. Prenez le temps d&apos;inspecter chaque pi&#xE8;ce &#xE0; la recherche de signes d&apos;usure ou de dommages, en particulier le joint, les ressorts et les composants mobiles. Le remplacement des pi&#xE8;ces us&#xE9;es contribue &#xE0; garantir des performances fiables et prolonge la dur&#xE9;e de vie de la t&#xEA;te de lames. Remontez la t&#xEA;te aux lames en suivant les &#xE9;tapes dans l&apos;ordre inverse. <img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026021916-c7af223c-4ccd-476b-b6c4-1d07139b1ffb-19%20-%20bh%20showing%20blades%20head%20frame%20empty.jpg" style="width: 669px;" class="fr-fic fr-dii"> <h2 id="prendre-soin">Prendre soin</h2>Prendre soin des composants de votre re:Mix contribue &#xE0; prolonger sa dur&#xE9;e de vie et &#xE0; lui permettre de remplir sa fonction. Chaque fois que vous le nettoyez, l&apos;entretenez ou le r&#xE9;parez, vous contribuez &#xE0; r&#xE9;duire les d&#xE9;chets et &#xE0; prolonger la dur&#xE9;e de vie du produit. Chez Open Funk, nous pensons que les produits doivent &#xEA;tre utilis&#xE9;s, entretenus et maintenus en &#xE9;tat de marche &#x2014; et non jet&#xE9;s. Vos efforts font une r&#xE9;elle diff&#xE9;rence. Merci de participer &#xE0; cette d&#xE9;marche. &#x2014; Open Funk

Comment demonter la tête aux lames

Tools Required:<ul><li>Screwdriver with Torx 10 (T10) tip (Use adjustable torque if electric)</li><li>Screwdriver with 3mm flat-tip&#xA0;</li></ul>&#x26A0;&#xFE0F; Ensure that re:Mix is unplugged from the socket, electric shock risk 1. Lay the re:Mix on it&apos;s back (with the knob facing top).2. Spot the hole on the right of the knob and with the flat tip screw driver gently unscrew it.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080313-67b9b9e7-f2de-4d39-8b04-1a3d5dd84f60-1.png" style="width: 692px;" class="fr-fic fr-dii"> 3. Once loose enough, pull the knob out to discover the tip of the rotary switch.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080313-f37160d9-0980-4817-987b-d94ac7177200-2.png" style="width: 698px;" class="fr-fic fr-dii"> If just replacing the speed knob, push the new knob in with the black line facing the 0 on the speed sticker and screw it back in, turn to test.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080313-8ec1fdf8-734a-417d-bd0b-3dba38a036f8-doc%20(8).png" style="width: 698px;" class="fr-fic fr-dii"> If replacing the rotary switch:4. Unscrew the four edge screws on the front panel and gently turn it around<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-1c228bcf-716b-40d5-8808-9cc210ca22c2-step%204.png" style="width: 698px;" class="fr-fic fr-dii"> 5. Behind the front panel and unscrew the two screws attaching the switch to the panel.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-3e94f709-24f7-4d75-85bb-9185845c78f1-step%205.png" style="width: 695px;" class="fr-fic fr-dii"> 6. Pull the rotary switch out and insert the flat tip screwdriver next to the the blue wires and gently wiggle the blue wires free.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-ec386fde-0faf-4ea8-b69e-7b6985797307-step%206.png" style="width: 698px;" class="fr-fic fr-dii"> 7. Using the new rotary switch and reused screws tighten the screws on the rotary switch.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-5bfe31f0-0a00-49bc-8ee9-36bcf33bc0b3-step%207.png" style="width: 687px;" class="fr-fic fr-dii"> 8. Screw the rotary switch with flat side facing right of the front panel.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-0f5a5982-99c7-468b-ab28-5897cb0614c5-step%208.png" style="width: 698px;" class="fr-fic fr-dii"> 9. Attach the light blue wire to the left top of the rotary switch and the dark blue wire to the right top of the rotary switch.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-b5ab0510-8376-4734-8830-7f1664b21431-step%209.jpg" style="width: 397px;" class="fr-fic fr-dii"> 10. Place the panel back on and screw the four edge screws back in.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-bf2afbd2-63d8-4d10-b4d5-2dff42c83efa-step%2010.png" style="width: 698px;" class="fr-fic fr-dii"> 11. Place the knob back in and screw in place, turn to test.<img src="https://attachments.gorgias.help/MNVgn6mnkKN21j8B/hc/MdAV17qgZr6ZWgaX/2026080314-2eea1e3d-a7b7-4d59-89f6-9fad26a0f0d7-step%2011.png" style="width: 698px;" class="fr-fic fr-dii">

Comment remplacer le commutateur rotatif

Oui. Nous avons commencé à proposer la tête des lames en tant que pièce séparée que vous pouvez acheter, et nous continuerons à ajouter le reste. Vous pouvez demander une commande ou une pièce personnalisée à hello@openfunk.co. Veuillez indiquer le n

Oui. Nous avons commenc&#xE9; &#xE0; proposer la <a href="https://www.openfunk.co/collections/re-mix">t&#xEA;te des lames</a> en tant que pi&#xE8;ce s&#xE9;par&#xE9;e que vous pouvez acheter, et nous continuerons &#xE0; ajouter le reste.Vous pouvez demander une commande ou une pi&#xE8;ce personnalis&#xE9;e &#xE0; hello@openfunk.co. Veuillez indiquer le nom de la pi&#xE8;ce, votre nom complet et votre adresse.La liste compl&#xE8;te des pi&#xE8;ces, la liste des mat&#xE9;riaux et la documentation d&apos;assemblage sont disponibles sur notre <a href="https://github.com/openfunkHQ/reMix">Github</a>.

Commande de pièces de rechange

Consultez notre documentation sur <a href="https://github.com/openfunkHQ/reMix" rel="nofollow noopener noreferrer" target="_blank" id="isPasted">GitHub</a>

Open source: Guide d'assemblage, liste des matériaux et documentation technique

Si votre question concerne une commande, veuillez indiquer votre numéro de commande ou le numéro de série situé au bas de l'appareil (par exemple S12345).

🇫🇷

🇬🇧

🇩🇪

Open Funk

Réparation et dépannage